There are two ways to set up Canon PIXMA MG3540 Wireless
connection. The first on is WPS connection method and the other one is Standard
connection method. Both steps are given below. If you need any assistance, then
you can go to set Up PIXMA MG3540 Wireless help.
WPS Connection Method
It is the easiest method for connecting the PIXMA MG3540
Printer to a network without password. Before you go through steps of WPS
Connection Method some conditions need to be fulfilled which are:
·
First of all, the access point must have a
physical WPS push button available. If the WPS push button is not available,
then you can use the instructions in the Standard Connection Method.
·
Second thing is that, your network must be using
the WPA (Wi-Fi Protected Access) or WPA2 security protocol. Almost every WPS
enabled access points use this protocol.
Steps for Connecting PIXMA MG3540
through WPS
·
First of all, switch on the printer.
·
Then, press the Wi-Fi button and release only it
after the alarm light blinks.
·
Now, when the Wi-Fi button light flashes blue, then
press the WPS button on the access point within 2 minutes. You can refer the
access point user guide for starting WPS on the access point.
·
The flashing of blue light next to the Wi-Fi
button will keep indicates that the printer is searching for the network.
·
The power lights and Wi-Fi will flash once the
printer starts connecting to the access point and will stop flashing and stay
lit once the connection between the printer and the wireless network is
established successfully.
Making Confirmation through Network
Settings
Follow the steps
given below in order to make sure that the printer is connected successfully to
wireless network:
·
Switch on the printer.
·
After that, load A4 or letter sized plain paper
sheet.
·
Press and hold the resume or cancel button until
alarm lamp 15time flashes and after that release it.
·
Network information page will be successfully
printed.
·
Refer the printout and you can check the name of
the connection under the “SSID”
(Service Set Identifier) field while the “Connection”
field should indicate “Active”.
Standard Connection Method
In case, if your router does not support WPS, then you can
use Standard Connection Method.
·
First of all, insert the CD which came along
with the Printer device. You can also download the manual and software of the Canon
Printer model number PIXMA MG3540.
·
Now, initial screen appears click the Next.
· A screen will displayed asking you to connect between USB or wireless connection.
· Your printer and lamp power should be turned on and click on Next.
· After that, click on connect to network tab.
· Next, after connecting to network click on Cableless setup.
· Now, hold the printer Wi-Fi button till the orange lamp flashes, and then release it after the second flash.
· Also make sure that blue (Wi-Fi) lamp flashes quickly and green power lamp is lit and click on the Next.
· Now, the screen appears for region selection and click on Next.
· Select the place of residence and click on the Next button.
· After that, select the software you wish to install and click Next.
· Next, click on agree of end user license agreement.
· Now, Installation Wizard Processes and click on Next button.
· At last, the screen appears with model number and name of wireless network. And Windows Cabless Setup is completed.
· A screen will displayed asking you to connect between USB or wireless connection.
· Your printer and lamp power should be turned on and click on Next.
· After that, click on connect to network tab.
· Next, after connecting to network click on Cableless setup.
· Now, hold the printer Wi-Fi button till the orange lamp flashes, and then release it after the second flash.
· Also make sure that blue (Wi-Fi) lamp flashes quickly and green power lamp is lit and click on the Next.
· Now, the screen appears for region selection and click on Next.
· Select the place of residence and click on the Next button.
· After that, select the software you wish to install and click Next.
· Next, click on agree of end user license agreement.
· Now, Installation Wizard Processes and click on Next button.
· At last, the screen appears with model number and name of wireless network. And Windows Cabless Setup is completed.
Hopefully, the above stated methods are helpful in setting
up your printer. If you are detecting any trouble in the process.
No comments:
Post a Comment